How to Use the OXVA NeXlim 2 and NeXlim 2 Mini: Beginner's Guide

To use an OXVA NeXlim 2, follow these four steps:
- Fill the pod from the top.
- Give a new pod 5 to 8 minutes to soak.
- Press the button five times to turn it on.
- Draw on the mouthpiece to vape.
The NeXlim 2 Mini has no power on step and fires when you draw. A mistake our support team sees often is the wrong pods. Xlim and VPrime pods do not fit, so check yours are NeXlim pods.
Shop the kits this guide covers, or read on for how to use them.
This guide covers the NeXlim 2 and NeXlim 2 Mini, two of the OXVA vapes we sell. It goes from the first fill to the error lights. Both take the same NeXlim pods and have the same Boost and Eco modes. They are set up differently, though:
- NeXlim 2: a colour screen and one button for everything
- NeXlim 2 Mini: no screen, a touch button and a 3-colour light
If you are still choosing between them, the specs, colours and box contents are on the product pages:
- OXVA NeXlim 2: 5 to 40W, 2000mAh, 0.85 inch colour screen with 10 themes
- OXVA NeXlim 2 Mini: 5 to 30W, 1500mAh, aluminium body and a 3-colour light
Both sit in our OXVA Xlim and NeXlim range, alongside the original NeXlim and the NeXlim Go.
Quick start
NeXlim 2: fill the pod, wait 5 to 8 minutes, press the button 5 times to turn it on, then draw. Press 2 times for Boost or Eco.
NeXlim 2 Mini: fill the pod, wait 5 to 8 minutes, push it in and draw. Tap the side button twice for Boost or Eco.

How to Turn On the OXVA NeXlim 2
Press the button 5 times to turn the NeXlim 2 on, and 5 times again to turn it off. Then draw on the mouthpiece to vape. There is no fire button to hold, as it fires when you draw.
Five presses is the same as most OXVA kits with a button, including the Xlim Pro 2 and Pro 3.
The NeXlim 2 Mini has no power on step in OXVA's manual. Fill it, push the pod in and draw. If nothing happens, check the light: red means the battery is under 30% and needs charging.
How to Fill a NeXlim 2 Pod
Both kits fill from the top, and the steps are the same:
- Take the pod out of the kit and open the fill cap on top.
- Fill it with nic salt or freebase e-liquid.
- Close the cap straight away, which OXVA say helps stop leaks.
- Leave a new pod for 5 to 8 minutes so the coil soaks through.
- Push the pod back in, set the airflow and draw.
OXVA say the UNITECH 3.0 pod primes in about 30 seconds. Both manuals still ask for 5 to 8 minutes on a new pod. Waiting the full time is what stops a burnt first puff.

OXVA NeXlim 2 Button Functions
Everything on the NeXlim 2 is done with one button, and these are the presses from OXVA's manual:
| To do this | Press the button |
| Turn on or off | 5 times |
| Switch between Boost and Eco | 2 times |
| Change the wattage | 3 times |
| Change the theme | 4 times, then once to lock it in |
| Turn the vaping animation on or off | 6 times |
| Reset the puff counter | 7 times |
| Read the on-screen guide | Long press |
NeXlim 2 Mini Touch Button
The Mini has one setting on its button. Tap the side button twice to switch between Boost and Eco. The airflow slider on the side does the rest, with three levels from tight to loose.
Boost vs Eco Mode
Every NeXlim pod has two mesh strips. In Boost both heat together, for a stronger hit and more vapour. That is up to 40W on the NeXlim 2 and 30W on the Mini.
In Eco the two take turns, which gives a smoother vape and makes each pod last longer. OXVA rate a pod at up to 30 refills in Eco and 20 in Boost.
As a starting point, use Eco on the 1.2 or 0.8 ohm pod for a tight draw. Use Boost on the 0.6 ohm for a looser one. On the Mini, the light tells you which mode you are in: several colours flash in Boost and one colour flashes in Eco. Our MTL vs DTL guide explains the two draws.
Boost Mode Not Working or Stuck in Eco
The NeXlim 2 switches mode on 2 presses, not 3. Three presses opens the wattage setting, which is why it can look stuck.
- Press the button 2 times quickly and check the mode on the screen.
- If it still will not change, take the pod out and push it back in firmly.
- Turn the kit off and on again with 5 presses, then try 2 presses.
- On the Mini, tap the side button twice and watch the light: several colours mean Boost.
How to Unlock Themes on the NeXlim 2
The NeXlim 2 has 10 screen themes. Three are open from the start, and the other seven unlock as you vape:
- The football theme unlocks at 100 draws.
- Each of the other six unlocks at random, somewhere between 500 and 1,000 draws.
- Press the button 4 times to scroll through the themes you have, then once more to lock one in.
- Press 6 times to turn the vaping animation on or off.
There is no code or app to unlock them early. The Mini has no screen, so it has no themes.

NeXlim 2 Mini Lights
The Mini's light shows the battery level when you vape, and flashes to warn you about a problem:
| Light | What it means |
| Green | Battery at 65% to 100% |
| Blue | Battery at 30% to 65% |
| Red | Battery under 30% |
| Several colours flashing | Boost mode |
| One colour flashing | Eco mode |
| Blue flashes 3 times | The puff went over 8 seconds |
| Red flashes 3 times | Short circuit |
| Red flashes 5 times | Too hot |
| Red flashes 10 times | Battery low |
Which Pod Should You Use
NeXlim pods come in three resistances, and these are OXVA's wattage ranges for each:
| Pod | Draw | OXVA wattage |
| 0.6 ohm | Looser RDL | 20 to 40W |
| 0.8 ohm | RDL or MTL | 12 to 32W |
| 1.2 ohm | Tight MTL | 10 to 25W |
The Mini tops out at 30W, so set the 0.6 ohm pod to 30W or under on it. The NeXlim 2 comes with a 0.6 and a 0.8 ohm pod, and the Mini with a 0.8 ohm.
Every NeXlim pod fits every NeXlim kit, the newer UNITECH 3.0 and the original UNITECH 2.0. They do not fit Xlim kits, and Xlim pods do not fit the NeXlim.
How Long the Pods Last
OXVA rate a NeXlim pod at up to 30 refills in Eco and 20 in Boost. Sweet e-liquids wear coils out faster, so change the pod when the flavour fades or tastes burnt.
Pod Leaking
Close the fill cap as soon as you have filled the pod, as both manuals advise. If an older UNITECH 2.0 pod keeps leaking, try the UNITECH 3.0 pod. Its condensate chamber is three times bigger to catch excess liquid, and it fits the same kits.
Shop the Kits and Pods
Both kits in this guide, and the NeXlim pods that fit every NeXlim kit.
NeXlim 2 Screen Messages
The NeXlim 2 shows a message on screen when something stops it firing:
| Screen message | What it means | What to do |
| Battery Low | The battery is low | Charge it |
| No Pod | The pod is not detected | Take the pod out, wipe the contacts and push it back in |
| Short | A short circuit is detected | Try a different pod |
| Timeout | The puff lasted over 8 seconds | Keep each puff under 8 seconds |
| Temp High | The chip is too hot | Leave it to cool before vaping again |
NeXlim 2 Not Turning On
- Charge it for a while over USB-C.
- Press the button 5 times to turn it on.
- If the screen lights but it will not fire, take the pod out. Wipe the contacts and push it back in.
Charging the NeXlim 2 and NeXlim 2 Mini
The NeXlim 2 charges at 5V/3A over USB-C, and OXVA say it reaches 80% in 20 minutes. The Mini charges at 5V/2A and reaches 80% in 30 minutes.
A USB-C cable comes in the NeXlim 2 box. OXVA don't list one for the Mini, so use the cable from your phone or another kit.
Older OXVA Kits
How to Use the Original OXVA NeXlim
The original OXVA NeXlim uses the same presses as the NeXlim 2, within 2 seconds each time. It has 3 themes rather than 10, and no vaping animation setting.
| To do this | Press the button |
| Turn on or off | 5 times |
| Switch between Boost and Eco | 2 times |
| Change the wattage | 3 times |
| Change the theme | 4 times |
| Reset the puff counter | 7 times |
| Read the on-screen guide | Long press |
Its UNITECH 2.0 pods fill through a silicone plug on the side, with the pod still in the kit. Close the plug straight away and leave a new pod for 5 to 8 minutes.
How to Use the OXVA NeXlim Go
The NeXlim Go has no screen and no buttons to press. It fires when you draw.
- Fill the pod and leave it for 5 to 8 minutes.
- Slide the switch on the side to Boost or Eco.
- Set the airflow, then draw.
The light on the front shows the battery: green above 65%, yellow from 30% to 65% and red below 30%. All four NeXlim kits take the same pods.
Every NeXlim kit is a refillable vape, so you fill the pod with your own e-liquid.
The 0.8 and 1.2 ohm pods suit 10mg or 20mg nic salts. The 0.6 ohm suits a lower strength with a looser draw.
To compare the NeXlim kits with other brands, see all the pod kits we sell.
Spare pods for every OXVA kit are in our OXVA pods range.
Pick up a NeXlim 2, a NeXlim 2 Mini or spare NeXlim pods.
More vaping guides
Frequently Asked Questions

Written by
Shane Margereson
Founder of Ecigone
Shane has spent over a decade in the UK vaping industry, building Ecigone from the ground up into a five-time Ecigclick Best Online Vape Store winner. He wrote this article.
Shane quit smoking through vaping, and helping smokers make the same switch is why Ecigone exists.
As featured in
- The Sun
- Daily Mirror
- Daily Express
- Daily Star
- OK!
- Daily Record














