Pyne Pod Click 50K Vape Kit

Pyne Pod Click 50K Pod Kit

The Pyne Pod Click 50K (sometimes written pynepod) is a 50k (50,000 / 50000 puff) vape kit with three prefilled pods, dual mesh coils, and an OLED screen that tracks your battery, puff count, and power mode. Each Pyne Pod Click 50K comes loaded with 36ml of 20mg nic salt e-liquid split across three 2ml pods and three 10ml auto-refill containers.

Three different flavours come in every kit. Pop one pod in at a time and swap it out when you fancy a change. Fifteen Pyne Pod Click 50K flavour editions are available with over 40 flavours across the range. When all three pods are empty, pick up a fresh set of Pyne Pod Click 50K refill pods and you're sorted.

Key Features

• 50,000 Puffs approximately per kit on Regular Mode (30,000 on Boost)
• 750mAh Battery USB-C charging, full charge under 1 hour
• 3 Pods Included three different flavours per kit
• Dual Mesh Coils fitted in every prefilled pod
• OLED Display battery level, puff count, power mode
• Dual Power Modes Regular at 10W, Boost at 20W
• Magnetic Click Pods snap in and out in seconds
• TPD Compliant UK legal post-June 2025

50K Puff Vape with Dual Power Modes

The Pyne Pod Click 50K pairs a 750mAh battery with USB-C charging that goes from flat to full in under an hour, enough for a full day of MTL vaping on Regular Mode. Two wattage settings tune the draw, switched by pressing the button twice.

Regular Mode stretches the 36ml of e-liquid further and pulls less from the 750mAh battery. Most vapers leave it on Regular for day-to-day use. Boost Mode doubles the wattage for a warmer draw and denser vapour but chews through liquid faster. The OLED screen shows an R or B so you always know which mode is active.

OLED Display and Puff Counter

An OLED screen on the front of the Pyne Pod Click 50K shows three things at a glance: battery percentage, the active power mode (R for Regular or B for Boost) and a running puff counter. The counter tracks usage across all three pods, so you always know how far through the kit you are.

Dual Mesh Coils

Every prefilled pod uses dual mesh coils. Mesh heats the e-liquid across a wider surface than standard round wire, so the flavour stays consistent right through the pod with no coil swaps or priming. The 20mg nic salt pairs with the MTL draw, and the kit fires on inhale - the button is only for switching power modes.

How to Set Up the Pyne Pod Click 50K

Setup instructions for the Pyne Pod Click 50K - it takes under a minute:

1. Charge the kit fully using a USB-C cable (not included in the box)
2. Take your first pod and remove all rubber plugs and stickers
3. Press the 10ml refill container into the base of the pod unit until it clicks
4. Click the assembled pod unit into the Pyne Pod Click 50K battery magnetically
5. Remove the mouthpiece plug
6. Draw on the mouthpiece to start vaping

When that pod is empty, pull it out and click the next one in. Same steps for each of the three pods.

Switching power modes: Press the button twice. The OLED screen shows R for Regular (10W) or B for Boost (20W).

Pyne Pod Click 50K Specifications

Pyne Pod Click 50K Flavours

Fifteen editions, each with three Pyne Pod flavours in one kit.

All editions use 20mg nic salt e-liquid.

What's in the Box?

• 1x Pyne Pod Click 50K Kit (750mAh battery)
• 3x 2ml Prefilled Pods (dual mesh coils fitted)
• 3x 10ml Auto-Refill Containers (20mg nic salt)
• 1x User Manual
• USB-C charging cable not included